高等级生物安全实验室通风空调系统冗余设计原则探讨

对比分析了国内外标准有关高等级生物安全实验室通风空调系统冗余设计的要求。结合我国已有高等级生物安全实验室,重点分析了送风机、排风机、排风高效过滤器冗余设计的具体实施形式和存在的问题,给出了冗余设计原则建议。     

Comparative analysis of formaldehyde and toluene sorption on indoor floorings and consequence on Indoor Air Quality

Indoor surfaces may be adsorptive sinks with the potential to change Indoor Air Quality. To estimate this effect, the sorption parameters of formaldehyde and toluene were assessed on five floorings by an experimental method using solid-phase microextraction in an airtight emission cell. Adsorption rate constants ranged from 0.003 to 0.075 m·h⁻¹, desorption rate constants from 0.019 to 0.51 h⁻¹, and the partition coefficient from 0.005 to 3.9 m, and these parameters vary greatly from one volatile organic compound/material couple to another indicating contrasted sorption behaviors. A rubber was identified as a sink of formaldehyde characterized by a very low desorption constant close to 0. For these sorbent floorings identified, the adsorption rates of formaldehyde are from 2 to 4 times higher than those of toluene. Two models were used to evaluate the sink effects of floorings on indoor pollutant concentrations in one room from different realistic conditions. The scenarios tested came to the conclusion that the formaldehyde sorption on one rubber (identified as a sink) has a maximum contribution from 15% to 21% for the conditions of low air exchange rate. For other floorings, the sorption has a minor contribution less than or equal to 5%, regardless of the air exchange rate.     

增材制造技术在超高膨胀封隔器中的应用

石油和天然气行业不断关注增材制造技术在航空航天和汽车行业的应用发展。研发了利用增材制造技术的超高膨胀封隔器,该封隔器的支承环系统由增材制造。增材制造设计大幅减少了支承系统的构件数量,同时显著提高了膨胀能力和额定压力。密封元件系统与增材制造支承环安装在一起,提供了极端膨胀比、零挤压间隙和对不规则孔的良好适应性。分析和测试结果表明:直径膨胀比高达111%,与常规封隔器相比,提高50%以上; 至少涵盖5种线重的套管(外径相同); 在148.89 ℃的温度下,密封元件能够保持压力68.95 MPa。介绍了增材制造技术、增材制造支承环概念、增材制造材料力学性能、密封元件系统优化和测试情况,以期给我国的完井作业提供借鉴。     

油藏中后期减氧空气驱提高采收率机理研究

尕斯库勒油田E¹₃油藏已经进入高含水时期，储采失衡加剧，综合含水率达到了80%以上，原油产量下降，经济效益变差。为了提高油藏原油采出程度、改善油藏开发效果，调研了国内外减氧空气驱的机理研究以及现场试验的资料，建立了以油藏真实孔渗饱数据为基础的一维条形地层机理模型，并选取该油藏Y12-27井组进行了减氧空气驱可行性验证。研究表明:纵向顶部减氧空气驱驱油效果优于水驱和氮气驱；驱替压力对原油采出程度影响不大；注水转注气可以提高原油采出程度；对于减氧空气驱，由于低温氧化反应的作用，氧气浓度对原油采出程度有一定影响，但比较微弱，其中，氧气浓度为10%时，驱替结束采出程度最高；尕斯库勒油田E¹₃油藏属于注水开发“双高”油藏，适用于减氧空气驱；对于该油藏Y12-27井组，顶部减氧空气驱驱油效果好于水驱和氮气驱，建议氧气浓度超过10%时采取关井等措施。     

锂-二氧化碳电池阴极催化剂的研究进展

锂-二氧化碳电池通过捕获、转化二氧化碳为储能物质，既可以减少二氧化碳排放量又可以作为创新的储能装置，引起了研究者们的广泛关注。本文简单介绍了锂-二氧化碳电池的工作机理、发展历程和目前研究存在的难题，通过对研究工作的总结、电池性能的对比，将不同类型的催化剂进行了系统的分类和简单的概括，综述了催化剂的设计理念和研究现状，提出了催化剂目前存在的难题与挑战，并展望了催化剂未来的发展方向。本文主要针对锂-二氧化碳电池阴极催化剂的最新研究进展进行了详细的阐述，指出高效的阴极催化剂是促进锂-二氧化碳电池电化学反应动力学、降低充电平台和过电势的关键所在。     

A comparative study on hygroscopic and physiochemical properties of chicken powders obtained by different drying methods

Abstract

Different drying methods (spray drying (SD), vacuum drying (VD), microwave vacuum drying (MVD), and infrared vacuum drying (IFVD)) were applied in order to compare the hygroscopicity behavior of chicken powders. The hygroscopicity curves and glass transition temperature were used to evaluate the influence of ambient humidity and temperature on moisture absorption of powders. The results showed that the chicken powder dried by MVD had the lowest moisture absorption, followed by IFVD, VD, and SD. The hygroscopicity of SD chicken powders was different from other three kinds of chicken powders due to the physical properties of particles and the changes of protein secondary structure as detected by the Fourier transform-infrared spectrometer. For the three vacuum drying methods, the difference of protein secondary structure was the main reason of differences in hygroscopicity. Although MVD chicken powders were slightly inferior to SD chicken powders in taste, MVD chicken powders were the best in terms of smell and color as suggested by instrumental sensory parameter evaluations. It was found that MVD had a positive effect on reducing moisture absorption and maintaining sensory quality of chicken powders.     

基于压缩机-支架系统的异常噪声研究

针对某乘用车发动机转速在1 573 r/min，压缩机开启时车内噪声异常的问题，对样车进行试验分析与诊断，对压缩机-支架系统进行仿真分析，提出改进方案并验证改进效果。利用LMS声振信号采集系统采集振动噪声数据，采用频谱分析、阶次追踪等方法，并结合压缩机-支架系统模态仿真结果，确定车内异常噪声是压缩机轴频21阶与压缩机-支架系统3阶模态频率接近发生共振造成的。通过优化支架结构来提高压缩机-支架系统3阶模态频率以此来避免共振，并换装橡胶驱动盘缓和压缩机输入扭矩波动。将改进结构进行整车试验，结果表明：匀速工况空调开启时问题转速下，车内噪声降低了2.5 dB(A)；匀加速工况空调开启时发动机转速1 500~1 650 r/min区间，车内噪声无峰值，其余转速空调开启时改进前/后车内噪声基本不变，噪声波动趋势平缓。